Car stereos are important parts of a vehicle. This can be enjoyed when the individual is stuck in the traffic, hear the latest news or just listen to music. Installing a stereo requires precise procedures to be adhered in order for it to fully functioned. If one step is not followed, then the owner will have to do it again. If the individual is not capable of handling the installation, they can hire a professional to do it for them. When it concerns with car stereo san antonio, individuals have to know the basics of wiring to fully make the new device functional.
To install a new stereo, the old has to be taken out first. To remove it, make sure the vehicle is in parking brake and disconnect the negative cables located in the battery. This must be done first because it will prevent the vehicle from getting short circuit when doing the installs. This will prevent getting harm or lead to fire.
When installing the new one, match up first the wires. Match the new wires from the cars harness to the new ones harnesses. Every connector and harness are unique in its own right it would be relatively easy to install the new ones because everything is being matched up with the same color. Just to be sure, check out the diagrams illustrated from the manual and see if everything is connected correctly.
If there is no harness, then the wire has must be matched up manually. Every wire is coded by color and will match with the component. However, it is still better to study the diagram to avoid any mistakes. Connect the wiring. Individuals can choose between soldering or crimping. Soldering is able to provide a better and secure connection while crimping is easier and quicker to perform.
Pull out the necessary components. The components may be important but if the new installation will require to remove it, then do the process. Disconnect the components that are being wired directly into the car. Make sure that you will remember all their placements for returning them later. If possible, take a few pictures where they are located for easy access.
Tuck all in the wiring right through the dashboard. There might be some wires that will not slide back right inside the dashboard. Take the component with one hand and the other hand to tuck all the wires inside. Slowly tuck the wiring or else there might be a few wires that will need to be reconnected.
Ground the new stereos. If the device has a harness, the connection will be made once the harness is installed and matched up. If not, you will have to manually locate the wire, screws, and bolts that connects on the vehicles metal chassis. You will have to loosen the screw, wire, and bolt and slip the wires underneath to tighten it up.
Secure it. If the devices are using spring clips, then it will make a clicking sound when it is already locked in place. There will be no need to further secure it. If the equipment uses brackets and bolts, reused all the bolts that was being removed earlier and attached them in the same place before.
The process is difficult. However, if you learn the right procedure, then it can be done by yourself. There is no need for you to hire a professional to handle the process.
To install a new stereo, the old has to be taken out first. To remove it, make sure the vehicle is in parking brake and disconnect the negative cables located in the battery. This must be done first because it will prevent the vehicle from getting short circuit when doing the installs. This will prevent getting harm or lead to fire.
When installing the new one, match up first the wires. Match the new wires from the cars harness to the new ones harnesses. Every connector and harness are unique in its own right it would be relatively easy to install the new ones because everything is being matched up with the same color. Just to be sure, check out the diagrams illustrated from the manual and see if everything is connected correctly.
If there is no harness, then the wire has must be matched up manually. Every wire is coded by color and will match with the component. However, it is still better to study the diagram to avoid any mistakes. Connect the wiring. Individuals can choose between soldering or crimping. Soldering is able to provide a better and secure connection while crimping is easier and quicker to perform.
Pull out the necessary components. The components may be important but if the new installation will require to remove it, then do the process. Disconnect the components that are being wired directly into the car. Make sure that you will remember all their placements for returning them later. If possible, take a few pictures where they are located for easy access.
Tuck all in the wiring right through the dashboard. There might be some wires that will not slide back right inside the dashboard. Take the component with one hand and the other hand to tuck all the wires inside. Slowly tuck the wiring or else there might be a few wires that will need to be reconnected.
Ground the new stereos. If the device has a harness, the connection will be made once the harness is installed and matched up. If not, you will have to manually locate the wire, screws, and bolts that connects on the vehicles metal chassis. You will have to loosen the screw, wire, and bolt and slip the wires underneath to tighten it up.
Secure it. If the devices are using spring clips, then it will make a clicking sound when it is already locked in place. There will be no need to further secure it. If the equipment uses brackets and bolts, reused all the bolts that was being removed earlier and attached them in the same place before.
The process is difficult. However, if you learn the right procedure, then it can be done by yourself. There is no need for you to hire a professional to handle the process.
About the Author:
Get a summary of the factors to consider before selecting an installer of car stereo San Antonio systems and more information about a knowledgeable installer at http://www.baudiosound.com/car-audio-system now.
No comments:
Post a Comment